Taylor’s New Model #3 Frontier
Story and photographs by Mike Nesbitt
[su_dropcap style=”light” size=”5″]T[/su_dropcap]here are some, perhaps several shooters, who say the old Smith & Wesson New Model #3 was the finest single-action revolver ever made, and I’m certainly one of them. I have had two of the originals, both in .44 Russian, and that’s why this new copy of the original New Model #3 feels so good in my hands. Holding and shooting this version from Taylor’s & Co. is like shaking hands with an old friend.
Before telling you about this new gun, let me quickly present a little bit of S&W history. After the Russian Model #3 and the Schofield version of the Model #3 had been made, the New Model #3 was introduced in 1878. This single-action revolver proved to be fairly popular, although not as popular as their .44-caliber, top-break, double-action revolvers. S&W lengthened the #3’s cylinder from 1 and 7/16 inches to 1 and 9/16 inches, adding an eighth of an inch to the length of the cartridges that could be used. This was meant to make their revolver available for the popular .44-40 cartridge, and like Colt, they called it their Frontier version. The S&Ws in .44-40 did not prove to be as popular and several of their .44-40 single-actions and were converted back to .44 Russian. By 1908, the New Model #3 was discontinued.
This New Model #3 Frontier by Taylor’s and Co. has a 6.5-inch barrel (5-inch versions are also available), and the cylinder is removable after taking out the screw in the top strap.
One of the best options that could be found on the original S&W New Model #3 revolvers was target sights. Instead of having the tiny rear sight on the pivot point of the top latch, the target version had a very nice rear sight on the end of the top latch just over the hammer. Moving the sight to the back or rear of the top latch increased the sighting radius by over half of an inch, and it gave the shooter a very nice flat-top rear sight with a deep notch. The rear sight on the target version is adjustable for windage by loosening the screws that hold the sight in its slot and sliding the sight to the right or left, which is quickly and easily done. The new Taylor’s version copies the original model and the easy-to-see rear sight can be appreciated all over again.
Authenticity is very important to me and the profile of this New Model #3 is very good. Taylor’s selected the .45 Colt chambering because of that cartridge’s popularity in the cowboy-action arena; however, I loudly recommend they add more caliber options. For those of you who prefer maintaining authenticity, the original New Model #3 was made on special order and chambered for the .45 S&W Schofield cartridge. In fact, in the book Smith And Wesson 1857-1945, there is a picture of an original New Model #3 with target sights and a 6½-inch barrel in .45 S&W caliber, almost a twin to the replica we’re talking about now.
Mike Nesbitt sits for a shot with black powder at a distant target. (JOHN WEGER).
Even more important than authenticity is how well a six-gun shoots, and this revolver shoots pretty well. The first loads that I tried with this Colt .45 used 32 grains (by volume) of Olde Eynsford 1-1/2F under a 235-grain bullet. With that black powder load, I quickly learned to grip the gun a little tighter because the recoil caused the gun’s trigger guard to hit my middle finger hard enough to really make it very noticeable. Also, somewhat because of my relatively loose grip, those shots went high and the sights needed to be held even lower than a typical six-o’clock hold. It took a few shots to learn where the gun was hitting, and after that hits could be counted on.
John “Sepp” Weger was my partner for most of the shooting, and for him this six-gun shot much closer to his point of aim. John is younger, a lot stronger than me and he gripped the gun more firmly, which considerably decreased the muzzle’s ability to climb.
While most of our shooting was done using black-powder loads, some tamer smokeless loads were also tried. The smokeless loads had 7.5 grains of Unique under a 250-grain bullet, a comfortable load for the Colt .45. These bullets were cast from Lyman’s old standard mould, #454190, and even though we did not chronograph this load, it was definitely good for cowboy-action shooting and general use with this Colt.
Five shots were fired across a benchrest using both hands. The sights were held at six o’clock on the bullseye and I’d say we achieved a really good group, even with the low flier that happened to go right through the X ring.
Some finer shooting could be done if the easily adjustable rear sight was moved just a touch to the right to correct the windage, but an even bigger improvement would be to give this gun a better trigger pull. While Uberti is known for making fine guns, they really do need to tone down their springs a bit. This Colt has a very stiff trigger pull which simply must be fixed. This is my only critical remark.
In addition to asking for softer springs and a lighter trigger pull, I will not hesitate to ask Taylor’s to follow a bit more in S&W’s footsteps and release this revolver in .44-40 caliber as well as .44 S&W Russian, or even .44 Special. Adding those chamberings, in my opinion, would increase the options for buyers to select from, and that could only increase this revolver’s popularity. I will conclude my begging by saying I hope their first New Model #3 Frontier made in .44-40 comes to me. ASJ
Author’s note: If you are ready to own a perfect replica of history that you can pick up for about $1,053, visit Taylor’s & Co. at taylorsfirearms.com.
Posted in Black Powder Tagged with: Black Powder, Mike Nesbitt, Revolver, Taylor's, Taylor's New Model #3