Evaluating Guncrafter Industries’ Model No. 4 50 GI
Story and photographs by Oleg Volk
Handguns are almost always inferior to riﬂes in terms of accuracy and stopping power. Since defensive ﬁghting usually happens up close, those qualities are important, but casual carrying of long guns is not socially acceptable in much of the world. The solution is to use the most powerful handgun that’s still practical for unsupported ﬁring. Guncrafter Industries Model No. 4 Hunting pistol attempts to create exactly that kind of weapon by combining 6 inches of barrel with a .50-caliber bore, the largest legally possible without National Firearms Act paperwork. That way, the projectile already has an impressive frontal area, 23 percent wider than .45 ACP, and 15 percent higher velocity for the same 230-grain bullet weight. For hog hunting use, slower but much denser 300-grain bullets are available. While less energetic than a hot 10mm auto load, the 50 GI is more efficient by not having to use as much of the kinetic energy to expand the projectile.
Guncrafter Industries Model No. 4 50 GI packs a powerful punch, whether you’re carrying for self-defense or hunting hogs.
The 50 GI accomplishes all that with the pressure of only 15,000 pounds per square inch. With the 6-inch barrel, especially, it gives much-reduced muzzle blast compared to other powerful defensive chamberings intended to supplant .45 ACP. While the case has a rebated rim like .50 AE, it’s straight rather than tapered. Seven cartridges ﬁt a regular 1911 magazine.
Gun reviewer Oleg Volk reports that the plain rear sight combined with a tritium front sight works well in moderate light, and it’s easy for the eye to pick up the chartreuse vial.
Recoil was the same as with a standard .45 ACP Government model, and the pistol showed impressive practical accuracy. Fired at the rate of about a shot per second, Model 4 gave one inch dispersion at 10 yards with all four loads. The sights as supplied were regulated for 230-grain HP and 300-grain JFP ammunition, with 185-grain HP hitting slightly lower and a 275-grainer an inch higher. At 25 yards, the groups predictably scaled to 2.5 inches, which is quite good for a ﬁghting pistol with iron sights. The combination of plain rear sights and tritium front worked well in moderate light, with the eye focusing on the vial with ease. With the long slide providing a nice forward balance, the sights returned on target readily. Overall weight is only a couple of ounces more than a regular M1911. The pistol is available in a wide variety of ﬁnishes and with various sight options.
Unlike the texturing on some high-powered handguns’ grips, the 50 GI comes with enough to hold onto it while it kicks, but isn’t so rough that it’ll chew up your hands at the range. The reviewer reports that while it shoots like any 1911 out there, the difference is in how much impact it delivers downrange.
Magazines required a good smack to seat on a closed slide when full, and dropped free when empty. The textured slide release worked well, so that I didn’t even bother with dropping the slide with the weak hand. The degree of texturing was sufficient for retention, not enough to abrade the hands. Unlike .357 Coonan, the Model 4 in 50 GI didn’t require conscious wrestling back out of recoil. It shot like any other 1911, with the sole difference of delivering a greater impact downrange. The report was not noticeably different. The muzzle ﬂash was not visible in daylight.
DEAD FOOT ARMS
So for the cost of dropping the full capacity from 8+1 to 7+1, it is possible to get a well behaved but more powerful weapon with the familiar form factor. The only down side I found has been the price: the pistol lists for a bit over $4,100, magazines are $50 each, and the ammunition runs $30 to $50 per 20-round box. I plan on talking to a couple of manufacturers to see if cheaper target ammunition may be developed for practice. AmSJ
For Half A Century, This Unassuming Riﬂe Has Made It Easy For Owners To Teach An Old Dog New Tricks
STORY AND PHOTOGRAPHS BY TOM CLAYCOMB
I’m convinced that the Ruger 10/22 is the most popular .22 riﬂe of all time. Not only is it a great little riﬂe right out of the box, but there are probably a million aftermarket items available that enhance its functionality even further, making it the most “trick-out-able” gun on the market.
Now, your vote may be swayed by the current AR platform rage, but that involves multiple calibers and brands. I’m talking about the most popular single gun, and the Ruger 10/22 owns that honor, hands down.
Not bad for a riﬂe that ﬁrst hit the market in 1964.
The 10/22 became my go-to riﬂe pretty quickly. How could I not love it? It’s extremely dependable, accurate and, as I mentioned, you can trick it out as much as you want. But it was my quest to hunt the elusive whistle pig (which in southern Idaho, where I shoot, refers to a Townsend’s ground squirrel) that led me to desire a higher level of accuracy, which in turn led to this article.
I love hunting varmints in the spring, and on good days I’ll shoot 400 to 500 rounds at these ornery targets. But if you’re like me when shooting hundreds of rounds using a gun with a small capacity clip, you’ll get frustrated, and I mean fast. In fact, it’s easy enough to get frustrated if you don’t have two or three fully stocked 25-shot banana clips on hand.
As my experience progressed, it got to be fun to see how far out I could hit whistle pigs. I hit one a year or so ago at 197 yards, and then another at 207 yards. If they hold still and let you get three shots to zero in, you can hit them out there. Of course, the gale-like winds we encounter regularly out on the high plains here in Idaho don’t help with long-range shooting.
To determine which item helped my accuracy and how much, I shot first with the plain 10/22 and economical scope, then I added the VX2 Leupold and shot it again, added the Timney trigger and shot, and then the Brownells barrel and Boyd stock. At each step I measured groups.
I noticed that while sighting in with a new scope, I’d have one or two ﬂiers out of a 10-round group. Then, when I listened good, I observed that there’d be a diﬀerence in the loudness or volume of the report, which meant it had a little less powder than the previous shot.
I then begin to doubt the ammo more than my shooting ability, a conclusion that was conﬁrmed when my buddy told me that even with good ammo, match shooters weigh their bullets and kick out those with the highest and lowest weights. I also shot his tricked-out 10/22, and although I thought he might have gone a little overboard with his, it got me thinking about which steps I should take with mine to achieve a higher level of accuracy.
In other words, which items helped me and which ones did not?
Hunting whistle pigs requires a scope because they’re small targets. You may have to take head shots when they pop out of their holes, so I didn’t begin this test using open sights. In fact, with a cheap scope and Remington ammo I was already getting between .65-inch and 1.0-inch groups at 25 yards. Then I shot some Eley ammo and got my groups
down to .4 inches.
Installing a Timney trigger is very easy. Remove the one screw holding on the stock and remove the stock. Many times the pins holding in the trigger will fall out, but if not, push them out. Install the trigger, replace the pins and remount the stock. That’s it.
The ﬁrst thing I did was install a Leupold VX2 4-12 AO CDS scope that I’d had painted in the company’s Custom Shop to match my new Boyd stock. Now I could really focus in and I was able to get my shooting down to groups of .6 inches with the Remington ammo and .4 with the Eley.
My original trigger had a pull of 5.5 pounds but it had a rough spot and some drag, which hurt my accuracy. So after adding the scope I installed a Timney trigger with a 2¾-pound pull. This lighter setting aided my squeeze immensely.
Installing a Timney 10/22 trigger was super simple. In fact, my son-in-law located a YouTube video that showed everything we needed to do, so we did the ﬁrst one together. The video said to remove the stock and pull the pins. Well, we removed the stock and two pins fell out, so I looked at him and said, “I assume those are the two pins we’re supposed to take out.” They had been held in place by the stock, so the process couldn’t have been simpler.
Despite the wind being pretty bad, with the new scope and trigger I was able to shoot groups between .5 inches and 1.0 inch using Remington ammo, and with the Eley I was consistently getting .5-inch groups. I now felt as if I had a good shooting riﬂe.
The next step was to put on a Brownells barrel and a Boyd Stock. Removing the barrel was also pretty simple. First you remove the stock, and then there are two Allen bolts holding a block that pins in the barrel. Remove them. My barrel was tight, so I ran home and used a wooden dowel rod to tap it oﬀ. To mount it again, just reverse the
order of steps. Then I slid on the Boyd stock and tightened it down with the one screw. What a sweet-looking riﬂe!
The following day I had to teach some seminars at Sportsman’s Warehouse, but as soon as I was done I took oﬀ for the plains. Now, I didn’t measure it, but I’ll estimate that the wind was blowing around 15 miles per hour. The next day there was a little less, probably 8 to 10 mph, so that helped. But with my new, tricked-out 10/22, I was able to achieve .4- to .6-inch groups with the Remington ammo, and .2- to .3-inch groups with the Eley. I now had a shooter.
If you believe diﬀerent brands of ammo vary in your bigger caliber riﬂes (and I do), the variance is even more so with a .22. So on the ﬁnal day, just for the sake of this article, I shot four brands. Here were the best groups that I obtained with each brand.
Federal Target Grade Performance: 1.3-inch group
Winchester M22: .9-inch group
Remington Golden Bullet: .4-inch group
Eley Force: .2-inch group TEST PARAMETERS:
Tests were performed at 25 yards oﬀ a stable bench with Altus shooting bags;
Distances were set using a Leupold RS-1200iTBR/W Digital Laser Rangeﬁnder;
Five-shot groups were ﬁred;
Shooting was done out on the prairie, so wind was a factor. For example, using Eley ammo indoors, I believe I could have obtained .1-inch groups.
The Leupold Custom Shop matched the pattern of this Boyd stock.
Here is how I would rank (from 1 to 5, with 1 being the most important) which item most aﬀected and/or improved accuracy besides choice of ammunition:
1. Scope You must be able to pinpoint one spot or you just aren’t going to be accurate.
2. Trigger If you can’t get a good squeeze, you just aren’t going to be able to tighten up your groups.
3. Boyd stock My stock is super comfortable and I feel like I have a good grasp of my riﬂe. Does that really help the accuracy? I think it does, if only minutely. Your mind will not drift oﬀ thinking how awkward or uncomfortable it is to hold. And although it is not a factor on a .22, Boyd claims that they help reduce recoil on larger caliber riﬂes.
4. Bull barrel I think this add-on would play a bigger factor on hot days when you’re pouring out the ammo. A lighter barrel would get warm.
The famed Ruger 10/22 was already a great little rifle before author Tom Claycomb tricked it out using parts shown here.
5. Cool factor If you want to have a riﬂe that takes people’s breath away, a scope out of the Leupold Custom Shop and a Boyd stock will surely help. Tell Leupold what type of stock you’re buying and they’ll paint your scope to match it. What’s cooler than that? In addition, both companies have options too numerous to mention.
Here’s a different take on whether getting a Ruger 10/22 is worth it by Youtuber GunGuyTV.
zZz Custom Works is proud to introduce our latest conception, The Czech Pack.
The Czech Pack is a unique design innovation that resulted from collaboration with Lucky Dragon Industries and zZz Custom works.
Inspired by a vintage travel tote from the former Czechoslovakia, we approached Lucky Dragon Industries to redesign this timeless classic with a modern edgy flare.
Utilizing the most contemporaneous materials The Czech Pack easily transforms from a shoulder slung travel bag to a frameless backpack in seconds.
The Czech pack in the shoulder slung configuration has two outer pockets that are secured by industrial quality zippers and has external hardware for adding various accessories such as water bottles and key chains. As a backpack, the Czech Pack has a protective weather flap for the top enclosure, two shoulder straps, and access to the two outer pockets.
The Czech Pack is made with the highest quality materials available including nylon webbing, packcloth, ripstop, and various top quality fasteners. Assembled in the United States by experienced craftsmen utilizing contemporary techniques.
Originally intended for military applications as a sensitive site exploitation and data collection bag we have adopted a civilian version that has audacious fabrics and colorful accents.
Bartlein 30 cal, 1 to 10-inch twist, M40 contour barrel, chambered in .308WIN, cut down to 24 inches and threaded 5/8 x 24 with SAC’s custom thread protector.
The American Shooting Journal spoke with Mark Gordon, owner and founder of Short Action Customs. They build precision rifles specifically designed for the ultimate in discerning and elite shooters. Gordon is also the lead sponsor for today’s top Precision Rifle Series shooter David Preston. Here is what Gordon had to say:
Mark Gordon I got started with PRS as a precision-rifle builder to see what our rifles would have to go through. Most importantly, it was to see what the shooters demanded out of their rifles and what they needed to be successful. The bottom line is these rifles have to work every time without fail, be extremely accurate and practical to use in the field.
Manners T5A right-hand stock with a signature SAC rifle-pillar bedding, and finished with desert-digital camo from Custom Gun Coatings.
ASJWhat is it that is creating such explosive growth with competition precision shooting?
An MMI Tru-Tec Melonite action and bolt, which prevents any galling of the metal and increases lubricity.
MGI believe it’s because these shooters have a desire to be proficient with their equipment and they want to know their limits. With a mixture of classic prone shooting and demanding positional shooting, the competitors are exposed to a large spectrum of disciplines at these matches. Lastly, the best place to do that is under strict time limits and lots of stress while other competitors watch. With many more club and national-level matches popping up all over the country, you can expect the sport to grow exponentially.
ASJYou currently sponsor the number one shooter in PRS. Tell us more about how that happened.
MGWe started our first rifle build for David Preston in early 2014 after developing a relationship with him from previous PRS matches. At that time, Preston was familiar with our rifles and what they were capable of. Luckily for me he wasn’t shooting for a team at the time. We spoke on a few occasions, and I offered him a position on our team. After many rounds fired, rifles rebarreled and matches shot, Preston really started shooting to his potential. We do our very best to keep reliable and accurate rifles in the hands of PRS shooters so they can do their job.
Short Action Customs Alpha 11 action with an integral 20 MOA scope base, an integral recoil lug and an M16 extractor. The magazine well is cut for Accuracy International AW magazines.
MGThere are two types of rifle builds that we love doing the most. The first is when a customer tells us to just do what we think is best. This allows us to take all of the leading-edge technology and components that we would use on our own builds and build the rifle we would want. It is great to have that kind of trust and confidence with our customers.
The second type of rifle build that we enjoy is when customers have us build rifles using components from manufacturers that we have not been exposed to. The parts industry is growing so fast, and as with any rifle build, it’s only going to be as good as the foundation it’s built on. So we really enjoy working with new components and learning about all the latest products.
Timney 520 Calvin Elite trigger with an Accu-Shot BT17 bipod rail and a their model BT10LW17 quick-detach bipod.
My personal favorite rifle build is configured to be agile, medium weight and run smoothly. We run Defiance Machine integral scope base and recoil lug actions called the Alpha 11, Manners Composite Stocks T6A 100 percent carbon-fiber stocks and Remington Varmint-contoured barrels from Bartlein Barrels. We typically finish these rifles with custom paint from Custom Gun Coatings. ASJ