May 26th, 2016 by Sam Morstan

Defouling, Best Bullets, Hunting, Accuracy And Cleaning

STORY AND PHOTOGRAPHS BY BOB SHELL

Editor’s note: We’re wrapping up our three-part series on blackpowder, which previously looked at its invention and early usage and then loading and safety, and now finalizes this issue with a discussion of defouling, types of bullets and more.

Blackpowder fouls a lot and if you don’t dry-brush out your barrel after every couple of shots, your bullet or ball will start becoming difficult to push down the barrel. If you brush it and dump out the residue, you can shoot all day doing that. I don’t recommend any type of lube, as you might contaminate the powder and it won’t help you in this operation. Use a tight shotgun-type brush for best results. Following those procedures and tweaking them to suit you should produce a lot of hours of enjoyable shooting.

Minié balls (left) and Maxi-Balls are the two basic bullets for blackpowder rifles between .36 and .58 caliber. The former was developed by a French officer in the mid-1800s, while the latter is sold by Thompson-Center. Author Bob Shell prefers Maxi-Balls for hunting. (MINIE BALLS: MIKE CUMPSTON)

As a note, some of the very early muzzleloaders had straight rifling to help deal with the fouling that blackpowder produces. Perhaps that’s where someone got the idea to twist it to stabilize a bullet. From a military point of view, they used smoothbores because of the mess that blackpowder produces. It takes more time on a battlefield to load a rifled firearm than a smoothbore. That is because the rifling fouls quicker, which makes it more difficult to load. When I am target shooting with a front loader, the bore is dry brushed after a few shots to keep it going. During the heat of battle a soldier doesn’t have that luxury. Of course, the usable accuracy was only from 50 to 80 yards with such weapons. They generally stood on a battlefield in plain view of each other and they shot until someone said uncle. Marksmanship wasn’t a top priority in this type of battle. You just shot into the crowd and hoped to hit someone.

Shooting a cap-and-ball revolver is essentially the same. Put the powder in and seat the balls tightly against the powder. One difference is you need to put some substance over the balls to avoid all of them going off simultaneously. I use something like Crisco, which always works for me, and I have never had that happen – and would just as soon forgo that experience. After loading the powder and bullet, then put on the caps but not before. That way you will avoid a possible accident. I have .36- and .44-caliber revolvers and they both shoot accurately with balls. I have tried bullets in them, but there is no practical advantage 99 percent of the time.

THERE ARE MANY TYPES of bullets out there for muzzleloaders. Some of the new ones are sub-caliber with sabots meant to increase long-range performance. I have some of those on hand, but for the purpose of this article I will stick with the basic stuff.

The basic bullets for rifles from .36 to .58 caliber are either Minié or Maxi-Balls. The Miniés have been around since before the War Between the States. They were invented by Capt. Claude-Étienne Minié, an officer in the French army in the mid-1800s. They are a hollow-base bullet that depends on the skirt expanding to provide a gas seal and good accuracy. They generally work as advertised, as long as they are cast soft. They are prevalent in .58-caliber weapons and come in various weights, from about 450 to over 500 grains. Their grooves are designed to help clean out the fouling, and with some types of lube will also soften the crud that accumulates in the barrel. They are the fastest projectiles to load, which wasn’t lost on militaries of the period. The .58 caliber was the most prevalent rifle caliber in the American Civil War. They gave good accuracy and produced horrible wounds. Many limbs were amputated because of the Minié ball, as they tended to shatter bones; with the state of medical care in that period, it was easier to cut off than save a limb. My experience is they tend to be more accurate with powder charges on the lighter side. Here again there is room for experimentation to obtain the best results in your weapon. I have also shot them in a .45 caliber and they were satisfactory in every way.

Thirty-six-caliber cap-and-ball revolvers are fun to shoot and are accurate at 25 yards, longer with practice. They also produce a nice pile of smoke when fired.

To be honest, my favorite bullet for hunting is the Maxi-Ball. They are available in .36, .45, .50 and .54 calibers. They resemble a slug and have two or three bands that engage the rifling. Between the bands is the area where you put your lube, and I use a lot to ensure that they stay against the powder. I also use a hard lube as opposed to a semiliquid type that may run into the powder, rendering it inactive. As with the other types, pure lead projectiles work the best, as they take the rifling well. I have seen some hard-cast slugs that were very difficult to load and seldom as accurate. I have a .50-caliber TC Hawkins and with my favorite load it shoots better than I can. A friend of mine has a .45-caliber Hawkins that he hunts deer with. We were out one day and after a while, I went over to where he was. I noticed that his Maxi was sticking out the end of his barrel. Good thing he didn’t get a shot. He had some store-bought slugs that were way too hard, so I molded him some good ones and took the others and made regular pistol bullets out of them.

FOR HUNTING, WHAT CALIBER should you use? As with everything, some common sense should be used. Keep in mind that you will have only one shot and that a reload will take some time. Even with pre-measured loads, a second shot won’t get taken quickly. Your quarry simply won’t stick around for it. That should encourage you to practice enough from hunting positions to get good enough to make that first shot count.

The .36 caliber is an excellent small game and pest load. It can be utilized for small game without excess meat damage. With a Maxi-Ball it can dispose of a coyote in short order. It should never be used for large game, as it just doesn’t have the horsepower for such work.

The .45 can be used for deer-sized animals with good shot placement, which is true of all hunting. The round ball is a bit light, weighing about 115 grains, which isn’t a lot. I would use a Maxi- or Minié ball for large game and confine the round ball to small animals.

The .50-, .54- and .58-caliber rifles with Maxi- or Minié balls can be used for game larger than deer. Round balls in those calibers will work well on big game, as they have enough weight to provide good killing power when used on deer-sized animals. The Maxis would work better on such game as elk, moose and bear. Just be aware that your first shot must count because you won’t get a second chance. And in some cases, you could be mauled by an angry bear that you didn’t shoot well.

This grouping shows the potential accuracy when hunting with blackpowder firearms.

Two friends of mine went on an elk hunt in northern Arizona last year. Both have .50-caliber Hawkins rifles and were using 370-grain Maxi-style balls that I molded. Since they didn’t want the corrosion, we went with Clean Shot, which produced good accuracy at 50 and 100 yards. Anyway, Tony harvested a fine bull, but Marty had the cap go off without firing the powder charge. The elk heard the pop and was long gone before he could get off a second shot. The second cap ignited the powder charge. He was wondering what a Hawkins rifle would look like wrapped around a tree. Anyway, those things happen even if you do everything correctly, but not very often.

The old smooth bore rifles aren’t accurate enough for most hunting situations, though the bigger calibers can do the job if you manage to hit something. Many of those were around .70 caliber, so they shot a large ball. The longest practical range with a smooth bore is 75 to 80 yards. If you purposely hit something beyond that, luck played a major part. I suppose you could load some shot and make it a clumsy shotgun at close range. I have done that and it does work OK. They are best used for reenactments and target shooting. The old blunderbusses were frequently used for small game hunting. They have a big opening, making them easy to load. Early on, hunters found out it was easier to hit a bird on the wing with a shot load as opposed to a single projectile.

EXCELLENT ACCURACY is a hallmark of many muzzleloading firearms and might amaze people with preconceived notions that they are not very powerful or accurate. Nothing can be further from the truth. Like modern arms, many muzzleloaders can outshoot their owners. A .50-caliber Hawkins can easily put three Maxi-Balls into an inch at 100 yards when shot by a competent marksman. Round-ball weapons also are very accurate and many can shoot well at 200 or more yards. It just takes a little more work and preparation. Cap-and-ball revolvers also can surprise you with their accuracy. Wild Bill Hickok shot an adversary at 75 yards through the heart with a .36-caliber cap-and-ball revolver. Of course, he was an excellent shot who practiced every day, but it shows what can be done.

There’s also the challenge, which makes it more interesting and fun. I recently took two shooters out and let them shoot my .36-caliber cap-and-ball revolver. They were amazed at the accuracy and how much fun it was. I believe both will be shooting black powder arms in the future as a result of that. In spite of the crude sights, at 25 yards a 3-inch-or-better group is entirely realistic.

AND FINALLY, BLACKPOWDER is hydroscopic, which means that it will absorb moisture very readily. That means that you must clean your weapon as soon as possible to avoid rust. With my muzzleloaders I remove the nipple and run hot water down the barrel with a little dish soap. I run a brush down the barrel until the water is clear. After that I run enough hot water through it to get it hot, then I let it dry. I then run a dry patch through it to make sure there is no water lurking about. I clean the nipple and the area around it and apply a light coating of oil on the gun. That works for me and I have used that method for many years and never have any problems with rust. There are a variety of products on the market that work well, but I prefer my method. Sometimes after cleaning a blackpowder weapon, it will be left it in the sun for awhile. Living in Arizona, I know that that will really dry it up in a hurry, getting the metal so hot you can hardly touch it.

FOR ANYONE CONTEMPLATING GETTING into blackpowder, by all means go for it. As shooting is about having fun, blackpowder will only enhance it. Done correctly, it is a safe and enjoyable hobby and lets us know how easy we have it in regards to weapons. Just imagine you are on horseback in a downpour with a band of Apaches chasing you. They are planning on giving you a close-cropped haircut and you have a cap-and-ball revolver you are trying to reload. It will help you appreciate your modern handgun and its cartridges even more. ASJ

Blackpowder and its many compositions – represented here by FFFFG L, FFFG L, FFG and FG R – represent a link to the shooting world of the past and an exciting one that is thriving today.

Posted in Black Powder Tagged with: , , , , ,

May 25th, 2016 by Sam Morstan

Part II of III – Loading And Safety

STORY AND PHOTOGRAPHS BY BOB SHELL

We began this three-part series on blackpowder last issue, where we covered its invention, refinement and today’s four grades – five, counting a special Swiss version.
This issue we turn to loading the powder and safety, and wrap up next month with tricks of the trade.
There are a few things that you should be aware of to get best results. First, always make sure your gun is empty. If you buy a new muzzleloader, then you can put a rod down the barrel and mark the rod to establish the depth that indicates an empty barrel. When preparing to load a used muzzleloader, remove the nipple where the percussion cap would be placed, and make sure you can see clearly through to the inside of the barrel. If it is blocked, the gun won’t fire, and the only thing you will get is a small pop from the cap.
A method often used to clear or establish a clear nipple channel is by firing a couple of caps without any powder in the barrel. Simply place a piece of paper or something light on your bench, and then aim the end of your barrel at the object and fire. The piece of paper should move when your channel is clear because the percussion cap alone is enough to cause a tuft of air. Once you have established that, you have a clear barrel and you are ready to load.

Muzzleloaders come in all sorts of varieties, calibers, styles and ignition systems. The one thing they have in common is the way they are loaded, hence the name. Fifty-caliber Lyman caplock (top left), .50- caliber Lyman flintlock (bottom left) and an original pair of 1837 French military caplock pistols (below, right).

PATCHING
When loading a round ball, a patch must be used in order for the ball to be accurate and prevent blow by, which would rob the shooter of power and accuracy. You can buy precut patches or experiment with your own. An old sheet makes good patch material because it is both tough and consistent in thickness. The patch should be placed on the muzzle, then the ball seated on top of it. It should have some resistance to seating but not an excessive amount, as you might end up with a ball stuck halfway down the barrel. There are signs that help to indicate if you are using the proper amount of patching. You can usually find the fired patches on the ground, especially if you are shooting a number of rounds. If the patch shows rifling marks without excessive tearing, then it is probably the right size. If there are no markings from the rifling, then this might indicate that the patch should be a little larger. If you do get a bullet stuck in the barrel, you can pull it out with a bullet-removing screw.
However, this can be quite a chore.

BALL LOADING
You should always use a measuring device to pour the powder into the barrel – never do it from a flask containing a large amount of powder. If there is a live spark from a previous firing, this will cause an explosion. Pouring a small amount of powder down the barrel will help minimize the harm if there still happens to be a smoldering cinder. This does happen – to the careless! There are adjustable measures made just for this operation. This practice is especially necessary if you are shooting patched balls, because some of the cloth might stay lurking in the barrel and can cause mischief. You can swab between shots to avoid that problem, but don’t count on this to thoroughly rid your barrel of hazards.
I knew a guy who participated in reenactments. He was on a crew that was operating a cannon with a 2-inch bore. His job was to swab the barrel then push the bag of powder down afterwards. The bag of powder weighed 1 pound. One time after the team fired, he swabbed and then shoved the powder down the barrel, instantly losing most of his right hand. There was still a cinder in the barrel from the previous bag, and when he pushed the powder down, it went off. The long rod with a disc he was using to push the powder down was the same diameter as the barrel. When the canon went off, the disc removed most of his hand because it became a projectile. Safety requires methodical steps and preparation.
Once the powder is in, you can seat the bullet. Initially, there will be a little resistance, but it shouldn’t be excessive. If it is, find out why before attempting to push it the bullet in too deep. A bullet stuck in the barrel is a pain to remove, although it can be done usually with a corkscrew-type device.

It is imperative that the bullet is solidly seated to the powder in the chamber. Otherwise, serious damage can occur to the firearm and shooter.

It is imperative that the bullet is solidly seated to the powder in the chamber. Otherwise, serious damage can occur to the firearm and shooter.

After you get your round started, follow through using your long rod to seat it. The bullet must be tight against the powder. If there is no resistance from the bullet going down the barrel, it might move forward creating some airspace, so be wary of that. This could destroy the gun and cause injury.
I knew someone who destroyed a .45-caliber that way. He required medical attention caused by splinters lodged into his forearm. If you are unsure, flick the rod against the load a couple of times. If the rod bounces, then it is ready to go. You can mark the rod with a piece of tape if desired for future loading once you establish your load.

Blackpowder-measuring tools were created for very specific purposes and are a much safer way to load a muzzleloader. Top to bottom above is a priming tool, powder measure and primer measure.

Blackpowder-measuring tools were created for very specific purposes and are a much safer way to load a muzzleloader. Top to bottom above is a priming tool, powder measure and primer measure.

Sometimes people forget to put the powder in first. This is a pain, but it can be resolved. Just take off the nipple and work some powder into the barrel. You should put at least 15 to 20 grains to have enough to shoot the ball completely out the barrel. Make sure that the projectile exits before trying a regular load. Compressed air can also be used to push the ball out. There are two types of people who shoot muzzleloaders: those who forgot to put the powder in and those who will in the future.

PHOTO 3A 30-30 ss 009 - CopyPRIMING
Just in case you bump or drop your gun, it is not a good idea to prime before you load. With a flintlock, just prime the  pan and you are ready to go. For this article we will stick with conventional muzzleloaders as opposed to inlines.

BACK TO THE POWDER
If you are new to this game, you might wonder how much powder to use. Ideally, a new shooter would spend some time with an experienced blackpowder user. There are also books that can help. Blackpowder doesn’t produce as much velocity as the smokeless variety, no matter how much you use. At some point the powder just won’t burn and will simply come out the end of the barrel. You can put an old sheet on the ground in front of the gun to determine if you have too much powder. This test can be very informative.
In my .50-caliber Hawkins, I use 90 grains of FFG black with a 370-grain maxi ball. My velocities run almost 1,300 feet per second, and the load is very consistent and accurate. I have tried more powder but the gain was negligible, thus wasn’t worth the extra powder. If you are shooting a .45-caliber with a ball, 70 grains is a good starting point. If you are using a .58-caliber rifle with Minié balls, then 60 grains is a good place to start. I find that lighter loads in these guns generally produce better accuracy.

Powder horns were and are still common among muzzleloaders. The horn is strapped to the shooter and stores the bulk of their powder.

Just like reloading, you might experiment with your gun to see which combination works best. There are several brands of powder out there, so if you like to experiment, try what is available in your area. If you order online, be prepared to pay a hefty hazardous material fee, so ordering a large quantity helps cut costs. I order it by 25-pound cases. There are also fees for just smokeless powder and primers, but not loaded ammo.

BULLET OPTIONS 

Bob Shell with his .50-caliber flintlock.

Bob Shell smoking up the range with his .50-caliber flintlock.

The round ball is the basic, most widely used bullet and has some advantages. It is often very light for the caliber, which reduces the amount of powder needed for workable velocities. Another advantage is it reduces recoil. Properly loaded it is very accurate and is used for all types of target shooting. For hunting, it’s OK for certain types of deer, but might lack the penetration for large, heavy-boned game, especially past 100 yards. Due to its low density, it doesn’t carry or penetrate well. However, a .36-caliber ball makes a splendid small-game round. There you have the basics of muzzleloading blackpowder. Stayed tuned for part III of What Is black Powder, where we cover tricks of the trade. ASJ

Loading blackpowder may seem like a simple process, but there are inherent dangers if steps are not completed thoroughly and methodically.

Posted in Black Powder Tagged with: , , , , , , ,

June 17th, 2015 by Danielle Breteau

Good Muzzleloading Starts Here

Story and photographs by Mike Nesbitt
Mike Nesbitt Take two

Mike Nesbitt

Getting started in muzzle-loading can be a little tricky because we can only be as good as our instructors. Finding proper help sometimes can leave a new shooter on the short end of the stick. The big problem is that new shooters probably won’t know if they are being taught or shown the right stuff or not.

The very best way to get started down the right trail with muzzleloading is to find a good club and look into their activities. If those activities interest you, that’s a great start because you’ll be surrounded by a gang of shooters who share your interest. Black powder clubs are easier to find than you think. Ranges or sportsmen’s clubs in your area should steer you in the right direction.

PHOTO 1 Mike Moran President of WSMA

Mike Moran went from the world of cowboy-action shooting to becoming the new president of the Washington State Muzzleloading Association in short order.

I met an experienced cowboy-action shooter named Mike Moran who suddenly got very interested in the primitive side of muzzleloading. It’s considered primitive because we use traditionally styled muzzleloaders and not the more modern styled guns, and we still like camping in lean-tos and tepees, as well as wearing buckskins at our events. These folks are referred to as “buckskinners.”

Moran thought such doin’s were worth a try, so he bought a rifle kit, put it together and then signed up as a shooter for the rendezvous of the Paul Bunyan Plainsmen near Puyallup, Wash. (In the 1800s, American fur traders periodically met at designated places to be reunited with friends and family during weeklong gatherings called rendezvous, during which the traders would camp out, practice their shooting and throwing skills and enjoy one another’s company.) Once registered, Moran asked if someone could give him some help or guidance and he was directed to join a group of shooters that I was guiding and scoring.

Since Moran introduced himself to me the day before a shoot, I was ready for him when we got to the firing line the next morning. Moran didn’t score very highly at that event; one of the reasons was that he had not sighted-in his brand new rifle.

Moran did afterwards, and his scores have made a steady rise since that day. In fact, he recently outshot me. He has now graduated so far that he uses a flintlock rifle (a bit more difficult to use over a percussion), teaches other beginners how to shoot muzzleloaders and is now the new president of the Washington State Muzzleloading Association, which is an organization dedicated to providing shooting experience and prizes to young shooters.

PHOTO 2

Craig Brown (second from the right) with his“gang” of Boy Scouts on the trail.

The Boy Scouts of America is another group that promotes muzzleloading for young shooters, and a couple of our local groups here in western Washington are Troop 310 from Rochester and Troop 141 from Tenino. Craig Brown, a range-safety officer and instructor, personally guides these groups of youngsters, along with some volunteer assistance, through wooded trails where the scouts get a chance to shoot muzzleloading rifles at hanging steel targets. Among the activities these scouts enjoy include attending the annual Rain-de-voo (Western Shooting Journal, April 2014) of the Puget Sound Free Trappers, a subgroup of the Capital City Rifle and Pistol Club in Littlerock, Wash., each year.

PHOTO 3 View of a flintlock on a Leman trade rifle

The flintlock can be described as a system of firearm ignition generally used between 1660 and 1850. The rifle seen here is a Leman, and it was considered a trade rifle. These were often swapped with Native Americans for goods.

 

PHOTO 4 Hawken Mountain Man Gun

This custom-built lightweight Hawken has a sidelock percussion with a copper cap on the nipple. The Hawken brothers of St. Louis were famous in the early to mid-1800s for building guns tailored to the mountain men of the time. These were generally heavier guns that were reinforced through the wrist with longer tangs and trigger guards, which helped keep the rifle from being damaged through hard use. 

While out on these trail hikes, Brown makes sure that the muzzleloaders are never primed (or capped) until the boys are on the firing line and in a firing position. He is the only one in the group who actually has percussion caps, which, of course, are necessary for firing. When a scout is in position, Brown caps the rifle, which prepares the already-loaded gun for firing. This process allows him to work with just one shooter at a time, making the activity very safe.

PHOTO 2a

The instructor “caps” or primes the rifle once the student is in position and on target.

The scouts shoot on the Puget Sound Free Trappers’ range and the club is in favor of the training and experience the scouts receive, so the boys are allowed to camp and shoot there for free. If the scouts pay anything at all, I would guess it is just enough to cover the costs of the powder, ball and percussion caps.

My own start into muzzleloading might be worth telling about. I was in my midteens and working part-time in Ed Hilton’s gun shop. Ed had an original “Kentucky rifle” in .40 caliber, a flintlock that had been converted to percussion long before I ever saw it. This was in the late 1950s, and at certain times when there were no customers in the shop, one of us would ask, “Who is buying the Cokes?” With that as a cue, Ed would get the old rifle and the horn and bag, plus a paper target, and step outside where the target was posted on a large stump. Ed did all of the loading and we’d each take just one shot. The shooter with the hit farthest from center had to buy.

At that time a bottle of pop from a machine that kept the bottles hanging by their necks while cooled in cold water was just 10 cents. The Cokes, and yes, Nesbitt’s Orange, were all very chilling and quite refreshing. Those dimes were more treasured than dollars are today, and buying the pops, which I usually did, took all of the money I had, but I never missed the opportunity to shoot that old rifle.

If you would like to know more about the Washington State Muzzleloading Association, you can visit them at wamuzzleloaders.com. ASJ

 

Posted in Black Powder Tagged with: , , , , , , , , , , , , , , , ,