March 3rd, 2017 by asjstaff

It means you can fire this thing on semi or full auto with a folded stock!

A modified bolt carrier for the AR-15, and adds a spring in a dual recoil spring system to cut down the total cycling receiver extension. It keeps the full-auto capability and eliminates bolt-bounce!


Dead Foot Arms has made this kit available, with a golding stock adapter and buffer tubes. The adapter means that the AR-15 can even be fired while folded, and the whole shebang is available for less than $500.

Video Transcription
Hey Crucible Arms here with you. Today we’re checking out the Deadfoot Arms Modified Cycle System. D’you think this truck gun might be short enough for you?

[shooting]

Or maybe a little longer?

[shooting]

Come along, we’re gonna find out together.

So the folks over at Deadfoot Arms were nice enough to send me this test system. They’re in production now, and available, and they sent it to me so that I could wring it out a little bit and give you my impressions. Today’s just an overview of the system itself, I’m going to be testing it over the next few weeks, and then I’ll do a more extensive follow-up video as we go along. But so far, I’ve been pretty impressed. Most of you with ARs know that if you’ve got a folded stock, the problem with them is they basically turn into one-shot wonders. What’s unique about this system is it will shoot either deployed or in its smallest configuration. That’s pretty slick. It uses a modified bolt and spring system in order to make it capable of shooting in either the deployed or un-deployed position. So far it’s worked really really well for me, this is a 300 blackout 9-inch barrel, so, wonderful wonderful truck gun, and we’re going to make sure this system does what it’s supposed to do, because it does, this might be my go-to truck gun from now on. But before we take it down and show you the innards, let’s shoot it s’more!

[shooting]

Empty. Ready to go?

So let’s take this system down, show you how it works. We always check for clear, as usual. Nothing there, we’re good to go. So what we do is, it’s a little different than a typical AR-15 takedown. You’re gonna pull the front pin first, I found this is a little easier if you do it this way, because this is under pressure. The buffer tube is right here. So now that we’ve got that one out, we’ll go ahead and push the rear pin out, and again because this is all under pressure, it pops apart. So, got a modified buffer tube there, we have a modified recoil spring and buffer assembly here, it’s two springs and the buffer. This actually goes back into the recoil system there, back into the buffer tube I should say. And this goes into the modified bolt-carrier. And what you can see immediately is, it is a much shorter carrier. So they shaved this down in order to put their modified buffer assembley on here, and this is the key to how this system works. Now you know when you’re messing with Soners design, you know, everything from here forward is the same, but you know when you’re cutting weight and soforth off the back of the carrier, it begs the question, is it really going to work the way that it should? will tell you it works so far so good. I’ve not had any issues, but I’m gonna want to do a lot more testing on this to make sure that it does do what it’s supposed to do.

So in order to get it back together, it’s not all that different than putting your typical AR back together. A little different. You’re gonna pop that in and all the way forward. Then you’re going to slide the buffer spring, or the tube assembley I should say, actually ‘recoil spring’. So slide that in, and you are gonna have to kinda now wrestle the whole thing back to where it belongs. And again, I wanna do this on camera, so it’s gonna be a little clunkier than it would normally be, but you’re basically gonna slide this whole thing back together. And again I apologize, trying to do this in-frame. There we go. Pop the pins back in, and you’re back in action.

Now my guess is there’s gonna be haters that just for that reason alone aren’t gonna like this system, that’s okay. But that’s the second time I’ve done it, I didn’t find that to be too horrible or difficult, and the system is back to being functional.

The Deadfoot Arms Modified Cycle System is very simple to install. It takes about ten minutes, and requires zero modifications to either the upper or the lower.

As you saw, deploying and collapsing the system is relatively simple. To deploy it, it is a friction lock, you simply grab it, pull it out, and you can pull the buttstock back to whatever configuration or whatever length that you like. There’s a little pin right here that you can move to various positions to get it to the length that you prefer. Now in order to get it back down, all you have to do is take this little detent button and you can shorten up the stock, and then there’s a small detent button over here, you can push it and it takes it out of the lock position, you can fold it back. So aside from the obvious benefits of this system, which is having a compact design that will allow you to shoot repeatedly in semi-automatic folded or deployed, the system doesn’t add any additional weight. If you use this T-rex buttstock along with this system, you are basically at the same weight that you would be if you had the traditional buttstock system and a traditional buffer tube on here. So you’re not sacrificing weight for functionality.

So that’s the short and dirty version on the Deadfoot Arms Modified Cycle System, I wanna thank Russ and the boys with Deadfoot Arms, they are combat veterans that designed this system, are producing it, and have it to market now. I appreciate them sending me a unit to test. I will be doing so over the next few weeks, give it a run for its money, I’m running it on a 300 Blackout right now, I’ll also be running it on a 556, it also is evidentally supposed to be able to work with a suppressed platform as well, so we’ll run a suppressor on this bad boy and see what that looks like. In the mean time, appreciate your stopping by, take a look at Deadfoot Arms, they’re at www.deadfootarms.com, it’ll give you more information on this and how to get ahold of one, and you can also reach me on facebook at www.facebook.com/cruciblearms, or you can like this video, I’d appreciate if you would, subscribe to my channel, leave a comment down below, and share this with your friends. I think this is a pretty cool system. Until then, this is Crucible Arms, signing off.

Sources: Dead Foot Arms

Posted in Firearms Industry Showcase Tagged with: , , ,

January 25th, 2017 by jhines

Jerry Miculek set a new world record at SHOT Show 2017

History was made this week as Jerry Miculek set a new world record at SHOT Show 2017 by shooting the SLT drill in an amazing 1.59 seconds. During the Spread The Love (STL) drill, the shooter has to shoot 10 shots; first four to the chest and two to the head of the center target, followed by two to the chest on the right target and then the left target. Take a look at the record-breaking shoot below.

Miculek was already a world-record holder, but once again proved that he is one of the world’s best shooters. This shooting is absolutely incredible and deserving of the recognition that he has received for this most recent achievement.

Posted in Industry News Tagged with: , , ,