A well-made, accurate and good-looking AK-47 that is 100 percent made in the USA with no imported parts actually exists. Century Arms introduced the C39v2, 7.62x39mm semiautomatic rifle in 2014, and it continues to exceed our expectations. After receiving quite a bit of user feedback from the original C39, Century Arms made some intelligent changes and upgrades, resulting in the C39v2, which has set it apart from other AKs on the market. Even AK purists are having a hard time finding fault with their latest C39 variant.
While elegant isn’t a term usually associated with an AK-47, the C39v2 earns the descriptor. With a milled receiver machined from a solid 11-pound block of 4140 ordnance-quality steel and lightening grooves on each side, gone is the rough industrial look of the traditional stamped AK. Marry this receiver to the high-quality wooden forend furniture and Warsaw-length stock, finish the receiver and barrel inside and out in black nitrite, and you have one classy-looking rifle!
Century Arms’ C39v2 offers many upgrades from their earlier versions, and is California-law compliant.
The obvious upgrades to the v2 include the sights, magazine release and safety that have been changed from the original Century Arms C39. After much feedback they brought back the traditional AK iron sights, allowing those with standard AK sight tools to breathe a sigh of relief. The new oversized T-shaped extended magazine catch might appear to be cumbersome at first glance; however, just as oversized controls on pistols and shotguns have proven useful, the v2’s large release proved an asset for aggressive and fast magazine changes. Proof in point that bigger can be better. The safety has a very positive, crisp feel, and includes a notched detail that receives the charging handle and locks it in place, keeping the bolt open. In combination with the modified dust cover the C39v2 safety won’t over-rotate past the dust cover, as with some stamped AKs, and is easy to remove for servicing.
The integrated Green Mountain barrel has a 1:10 twist and a concentric left-hand 14×1 metric thread that comes equipped with a chevron muzzle break.
Century Arms didn’t cut corners when it came to components. Green Mountain makes the C39v2’s 16.5-inch barrel with a 1:10 twist and a concentric left-hand 14×1 metric thread that comes equipped with a chevron muzzle break. They chose a high quality barrel and used black nitrite to coat it inside and out, which ensures longevity and accuracy over the life of the gun. Similarly, the double-stack bolt design and lightening slots in the bolt carrier – whether you are a fan of that feature or not – show quality machining throughout.
Century Arms has streamlined the lines of this AK by engineering a milled receiver using 4140 ordnance-quality steel and lightening grooves on each side.
Century Arms answered the demand for a better trigger in the v2 by creating and manufacturing the RAK-1 trigger group. Using a double-hook single-stage trigger with Wolf springs, the RAK-1 is arguably the closest thing to an AK match-grade trigger on the market. An innovative relief cut allows the RAK-1 to be used in receivers designed to only accept single-hook triggers. Most AK triggers require polishing on the top to eliminate bolt hang up. The RAK-1’s top-profile design is already optimized, making additional tweaking unnecessary. For an AK trigger the RAK-1 has very little uptake, breaks at 5 pounds and has a crisp reset. While this trigger is nothing fancy compared to what the M4 market is accustomed to, it is well made, does the job and fits other AK-variant rifles and pistols such as the RAS47, WASR, N-PAP and C39s.
But how does it shoot?Get the rifle off the bench and onto the range! Zeroing from the prone position at 100 yards with Wolf ammo, the C39v2 shot a consistent 2-inch group. Why zero at 100? Because friends don’t let friends zero AKs at 7 yards! Century Arms claims that the C39v2 shoots one minute of angle out of the box, which very well may be the case in the hands of a more experienced AK enthusiast.
Over the 500-plus rounds fired through this gun while testing, there were no malfunctions other than the most infuriating and common AK malfunction: running dry! The rifle cycled with boring reliably and smooth operation without interruption, as is expected of a well-made AK. If you love AKs, you probably love a pump shotgun for the physical handling required to effectively run both. Reloads are the best example: rocking the empty mag out with a new one and slamming the next one home isn’t a delicate operation. Simply put, the more aggressive you are with this AK, the better it performs.
Concerning the C39v2’s durability: It’s an AK. They were designed to be driven over, dropped, submerged, survive the Russian “push up test” (where the person doing the pushup balances the AK upright on the magazine, and holds each end while conducting pushups – all the weight, pressure and balance point is on the magazine resting on the ground) and run as intended, depending on the volume of gravel accumulated in the action. That being said, it’s easy to tear down, clean and get back up and running because, well, it’s an AK. Being made with quality components only stands to increase the C39v2’s durability and longevity in the hands of a hard-use discerning shooter.
Downsides to the C39v2?For some, the additional weight from the milled receiver that brings the rifle to a whopping 8.2 pounds may be an issue. Because Century Arms designed the receiver to be compatible with after-market modern Kalashnikovs (slight modifications may be required) and polymer furniture, these components can be changed out if weight is that critical. Gym memberships may also be an option for consideration.
According to Tatiana, the only malfunction she encountered while testing the C39v2 was running dry.
The chevron muzzle break may be the only component that some would wish to change out. That being said, it’s a simple procedure, and arguably the only metal component on the rifle that may not suit an AK shooter’s tastes. A contemporary AK shooter will wish there was a side mount for optics while AK traditionalists may shed a tear when they find the C39v2 lacks a bayonet lug and cleaning rod. However, this allows it to adhere to California laws, and is available in a bullet button version to make West Coasters leap with joy.
Out of the box the v2 already has the majority of value-added upgrades most enthusiasts look to change in stock versions. Century Arms has delivered an affordable, quality AK with the added patriotic benefit of sourcing and making it entirely in the US. Given our nation’s ever-changing import bans and regulations, having an AK-47 manufacturer stateside that listens to its customers and is willing to evolve their product is a great asset to the US firearms community. As more shooters experience the C39v2 and appreciate it, the only question that remains is, can Century Arms keep up with demand? ASJ
Review by Gy6vids Youtuber:
-The shooting test is not an accuracy test but on quick target acquisition
-Gy6 takes the C39V2 through its pace by going through some target acquisition – doing single, double and triple taps with magazine change.
-A great feature that you can install is the increase paddle mag release. It will help you do magazine change quickly with this ambidextrious paddle.
-Gy6 also does some dirt torture testing, where he tosses the C39V2 into the dirt with the bolt closed and open and fires it with no problems.
-If you’re looking to decrease your trigger pull down to 3 lbs, have a look at CMC triggers.
Some advantages to having this weapon is the ammo.
-Ammunition, the 7.62x39mm has some oomph when compared to the .223 round. This obviously has more stopping power at close range and long ranges. For home defense, its perfect for close quarter encounter, its not likely that you will be sniping at your burglar.
-Ammo economics, for some high quality brands of 7.62x39mm costs about $225 per 1,000 rounds. (thats not bad)
Review by Tatiana Whitlock • Photography by Oleg Volk
[su_heading size=”30″]The Century Arms UC-9 Carbine remains a popular semiauto version of the classic Uzi.[/su_heading]
STORY AND PHOTOS BY FRANK JARDIM
[su_dropcap style=”flat” size=”5″]T[/su_dropcap]he classic Uzi 9mm submachine gun was developed by Uziel Gal in the 1950s for the Israeli military, and in its day was considered an excellent combat weapon. And although guns with similar features had become pretty standard by the end of World War II, the Uzi changed the paradigm for submachine guns with its compactness, ergonomics and easy handling.
These reasons are also why the gun continues to be replicated by a variety of manufacturers. One of these, Century Arms, Inc., has found success with their semiauto version, the Centurion UC-9.
The original Uzi was made mostly of welded metal stampings and had a rock-solid metal collapsible or ﬁxed wooden buttstock. It featured a simple blowback design, utilizing the weight of the heavy bolt alone to keep the action locked, and the recoil energy of the ﬁred casing to cycle it. The ﬁring pin was machined into the bolt face, and the weapon ﬁred from an open bolt. Though very heavy – over 9 pounds loaded – its good balance permitted one-handed ﬁring.
This compact balance was achieved by setting the 10inch barrel deep in the stamped sheet metal receiver so its breech was above the trigger. The bolt encased the barrel breach to about the midway point and the magazine was inserted up through the grip frame. All of the mechanical operation of ﬁring took place directly above the gripping hand rather than in front of it, as on a typical, much longer submachine gun (such as the MP40). The Uzi grip was positioned on the receiver slightly rear of center to counter the effects of recoil.
The Uzi saw use in the hands of good guys and bad through the 1980s, and was a staple in movies and on TV. Anyone who remembers seeing the attempted assassination of President Ronald Reagan on the news knows it was used by our Secret Service too. Seemingly out of nowhere, an agent pulled one out and stood watch as other agents wrestled the attacker to the ground. It remains perhaps the second most recognizable submachine gun in the world after the Thompson.
The Centurion UC-9 utilizes many original Uzi part designs, coupled with an American-made semiauto-only bolt and receiver.
ISRAELI MILITARY INDUSTRIES(IMI), the original maker, ﬁrst offered semiautomatic versions of the Uzi, and these guns are rightly considered the best. Other clones, both domestic and Chinese, soon followed. And, as parts kits from demilitarized IMI- and FN-made subguns ﬂooded into the American market, several other ﬁrms started making receivers for gun-building hobbyists to assemble their own semiauto guns.
The Centurion’s semiauto grip assembly and safeties.
Century Arms, already famous among collectors for their semiauto copies of post-World War II select-ﬁre military weapons, set about producing their own ﬁnished semiauto carbine. Their Centurion UC-9 utilizes many original-part designs coupled with an American-made semiauto-only bolt and receiver.
The UC-9 is mechanically identical to previous Uzi clones. It has a 16-inch barrel instead of the 10-inch one found on the submachine gun. One caution: 10-inch barrels for it are available on the parts market, but before installing one, you will
The rear aperture uses a 100-yard and 200-yard flip rear sight, but elevation and windage are easily adjusted at the front sight
need to register the gun as a Short Barreled Riﬂe (SBR) with the Bureau of Alcohol, Tobacco and Firearms and pay the appropriate taxes.
It ﬁres from a closed bolt using a striker and modiﬁed trigger components. The extra spring in the striker makes the bolt more difficult to pull pack than the fullauto version. The top cover is original, but the ratcheting mechanism is deactivated. That feature kept the bolt from ﬂying forward and accidentally discharging a round if the cocking handle slipped from the shooter’s grasp, and is useless on a closed-bolt semiauto.
The UC-9 will accept 25- and 32-round magazines.
The receiver has a rounded bar welded along the inside of the right side of the frame behind the ejection port. The semiauto bolt has a corresponding groove cut down its right side to clear this bar. Because of the bar, a full-auto bolt will not ﬁt in the receiver. The bottom left side of the bolt is milled away to accommodate the striker mechanism beneath it. The arm of the striker has a cut to engage the sear in the trigger mechanism. A portion of the bottom on the right side of the bolt is also relieved so it will clear the other side of the sear.
The Century Arms Uzi clone field strips easily into just a few parts.
The safety in the grip assembly is marked only “F” for ﬁre and “S” for safe. The thumb selector is blocked internally and cannot be pushed forward into what would normally be the full-auto position, though a stamped line indicating the “ghost” location is still there.
There are a few other differences between the semiauto Uzi and its full-auto ancestor. The semi’s push pin that holds the grip assembly onto the frame is larger (9mm versus 8mm), its sear is lighter and smaller, and machinegun barrels won’t ﬁt because of changes in the mounting points. All these changes allow the ﬁrearm to be sold as a normal semiauto long gun. OVER THE YEARS, Century Arms has received criticism regarding the quality control of the classic modern military ﬁrearms they re-engineered into legal-to-own semiautos. In their defense, much of this criticism has stemmed from a few bad apples spoiling the bunch. As any gun manufacturer will tell you, it’s hard enough making something work perfectly when you design and build it from scratch, and Century’s semiauto military clones are short-run projects compared to your typical sporting arm. It’s the difference between a few thousand units and tens of thousands.
I’ve never had a problem so serious that I had to return a ﬁrearm. I’ve heard of some over the years, but to my knowledge Century took care of each customer. And, in my opinion, on those occasions when Century didn’t get it right, they got it mostly right and it was a matter of some ﬁne adjustment to get it perfect. The way I see it, at the low price point they sell these collector ﬁrearms at, mostly right is still a bargain.
Shooters of smaller stature will have no problem firing the Centurion UC-9 at the zombie of their choice.
THE ACCURACY OF THE UC-9I tested surprised me in light of the short sight radius and less than comfortable metal stock. The rear aperture is set for 100 and 200 yards, but elevation and windage are easily adjusted at the front sight and I zeroed for a more realistic 50 yards for my testing. I set my chronograph up 15 feet from the muzzle. The UC-9’s weight made felt recoil light.
The most accurate load during testing was Federal American Eagle 124-grain FMJ, which averaged 2.38 inches at 1,232 feet per second, with the best group being 2.25 inches. All of the other loads I tested were 115-grain FMJ, and I achieved the following results:
CCI Blazer Brass averaged 2.59 inches at 1,396 fps, with the best group being 2.31 inches. Black Hills averaged 3.66 inches at 1,382 fps, with the best group being 2.19 inches. Winchester USA Forged steel case averaged 3.63 inches, with the best group being 3.75 inches, and Remington averaged 4.59 inches with the best group being 3.75 inches.
The author believes the UC-9 displays solid workmanship. Here is a comparison of some front-of-frame welding on an FN subgun (left) and the Century Arms UC-9.
The heavy, 12-pound single-stage trigger pull was sort of like pushing a refrigerator, but once I got it going, it moved along pretty easily.
Out of hundreds of rounds shot in testing, I had a handful of failures (ejection and sometimes chambering) that seemed related to the squared-off tip of the ﬁring pin penetrating the cartridge primer. More common was a chambering failure of the ﬁrst round from a fully loaded magazine. It would commonly get hung up at a 45-degree-angle point on the feed ramp and rim in the feed lips. However, the more I shot, the less this issue occurred, and I attribute it to the old military-surplus magazine, which I neither cleaned nor oiled.
General workmanship of the UC-9 was very good despite what some web critics claim. I compared the welding on the front of the frame to a part from a genuine FN demilled subgun, and the UC-9 was just as well executed, if not better.
There’s no practical advantage to a very heavy 9mm semiauto carbine like this, but if you have pangs of nostalgia for this historically important design, the UC-9 is a worthy clone at an affordable price.
Frank Thomas fires the Century Arms Centurion UC-9 at a recent Zombie Shoot event in Kentucky.
The MSRP is $749, but actual selling prices are closer to $650, and magazines are as cheap as $10 each.
For more on the UC-9 and other Century Arms ﬁrearms, visit centuryarms.com or call (800) 527-1252 to locate a dealer near you.