Having compensators on pistols is not exactly new. Competitors have been porting pistols for a very long time. Go look at any open division pistol in USPSA or IPSC. However, since the Roland Special came out, we have seen an increasing trend in compensators for Glocks. This has led to companies like Archon Mfg to make compensators. As a fan of compensated pistols, I got the opportunity to check out their Glock compensator.
Compensating For Something
For those who have not had the pleasure of shooting a compensated pistol, You are missing out. With a good comp design, the gasses help mitigate muzzle climb and recoil.
Archon Mfg’s take on their compensator is actually different than their competitors. While many other comps do screw onto a threaded barrel, Archon’s comp does not require thread locker or set screws against the threaded barrel. Instead, they split the female threads and have two screws on either side. So all you need to do is screw the comp onto the barrel, then time it to the right position and tighten the two screws so the comp clamps onto the barrel.
One added benefit to a comp on a Glock is that now your weapon lights don’t get coated in muzzle blast residue. Most of the gasses are going out the sides and top. Very little of it is blowing down to the light.
One minor issue is what threaded barrel you use. I am using a Lone Wolf Gen5 Glock 19 threaded barrel. Some threaded barrels have different lengths.
The gap between the Glock Comp and your slide will vary due to variations in barrel length on aftermarket barrels.
This is as close as I could get the Archon comp onto the G19X with the LW barrel. Notice there is a gap and the rounded corners of the Gen 5 disrupt the look. If I used a Gen4 or lower Gen Glock, the aesthetics where the slide meets the comp would look better.
Archon Comp, It’s Not Just For Glocks
While their compensator was designed for the Glock pistol, it is not limited to just the Glocks. You can mount this compensator onto any pistol with a threaded barrel.
Beretta 92A1 with Archon Mfg Comp
Sig Sauer P938 with Archon Mfg Comp
Does It Actually Do Anything?
So I am a bit spoiled as my benchmark for compensated pistols is my STI Steel Master race gun. It is the flattest and softest shooting 9mm handgun I own or have ever shot. So how does the Archon Mfg compensator compare? It is not in the same league. Is the disparity just from the compensator design? I don’t think so. The STI Steel Master is a purpose-built race gun. It was designed to run compensated. Adding a compensator to a pistol does not mean it is a race gun now. Just like adding a spoiler to a car does not make it a race car. So does the Archon comp work? Yes. There is an appreciable difference with the comp than without.
Take a look at the video below. It is a side by side comparison of the Glock 19X with and without the compensator. The left side has the Archon comp and the right side does not. Both shots you can see there is still muzzle climb. However, pay close attention to the position of the 19X after the recoil. The gun is physically higher and I have to bring the gun back down on target. With the compensator, the 19X does not jump as high and is quicker to bring back on target for the next shot.
The difference is very noticeable on smaller guns like my Sig P938. I think it is because the barrel is so much shorter and there are more gasses to make the comp work better. Just like a spoiler, you need more air/gas for them to be effective. In open division pistols, shooters typically load hotter rounds just so there is more gas to act on their compensators.
Is It Perfect?
No, it is not. But it is pretty good. The best part is their split design. It was very easy to swap between guns and since there is no set screw, the threaded barrels are not messed up. The overall length of the Archon compensator is a bit long.
- Precision machined from 7075 Billet Aluminum
- Type III Hardcoat AnAnodizedlack
- Weight: 0.9 oz.
- Dimensions: W: 1.000″ L: 1.375″ H: .800″
Mounting it onto a Glock 19 gives the overall length similar to a Glock 34. I would have preferred a Glock 17 profile as holsters would be easier to find. Luckily I have my holster for my Glock 35 and this fits perfectly.
One idea I had would be to alter their design so that the compensator does not need a threaded barrel. They could get a batch of long barrels and mill a slot on either side. Similar to the KAC Hush Puppy Beretta barrel. Reposition the set screws to line up with those slots and now you have a compensator/barrel set up for states that ban threaded barrels on handguns.
The Archon Mfg Glock compensator is quite affordable at just $69.99. Check out their website for more info.
Posted in Product Reviews Tagged with: Archon Firearms, Compensator, GLOCK, Glock 19, Glock 19X, Other Gear & Gadgets, Pistols, Reviews, Semi Auto, Shooting Accessories